|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
a FEATURES 10 V Output, 0.3% Max Adjustment Range, 3% Min Excellent Temperature Stability, 8.5 ppm/ C Max Low Noise, 30 V p-p Max Low Supply Current, 1.4 mA Max Wide Input Voltage Range, 12 V to 40 V High Load Driving Capability, 20 mA No External Components Short Circuit Proof GENERAL DESCRIPTION TO-99 (J-Suffix) NC 8 10 V Precision Voltage Reference REF01 PIN CONFIGURATION Epoxy MINI-DIP (P-Suffix) 8-Lead Hermetic DIP (Z-Suffix) 8-Lead SO (S-Suffix) NC 1 VIN 2 NC 3 4 7 NC 6 VOUT NC 1 VIN 2 8 NC 5 TRIM NC TOP VIEW NC 3 (Not to Scale) 6 VOUT REF01 7 GROUND (CASE) NC = NO CONNECT* GND 4 5 TRIM NC = NO CONNECT* The REF01 precision voltage reference provides a stable 10 V output that can be adjusted over a 3% range with minimal effect on temperature stability. Single-supply operation over an input voltage range of 12 V to 40 V, a low current drain of 1 mA, and excellent temperature stability are achieved with an improved band gap design. Low cost, low noise, and low power make the REF01 an excellent choice whenever a stable voltage reference is required. Applications include D/A and A/D converters, portable instrumentation, and digital voltmeters. Full military temperature range devices with screening to MIL-STD-883 are available. For new designs, please refer to ADR01. *NC = No Connect. Do not connect anything on these pins as some of them are reserved for factory testing purposes. SIMPLIFIED SCHEMATIC INPUT R8 R7 R14 Q15 Q8 Q7 Q14 Q13 R15 2 Q9 Q12 Q11 C1 R6 R3 R4 Q10 Q6 Q5 R13 Q17 Q21 Q18 Q16 Q19 OUTPUT 6 R12 16.7k 50k TRIM 5 Q4 R5 Q1 R1 R10 R2 Q2 Q20 Q3 1.23V R9 R11 2k GROUND 4 REV. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 2002 REF01-SPECIFICATIONS ELECTRICAL SPECIFICATIONS (@ V Parameter Output Voltage Output Adjustment Range Output Voltage Noise1 Line Regulation2 Load Regulation2 Turn-On Settling Time3 Quiescent Supply Current Load Current Sink Current4 Short Circuit Current Symbol VO VTRIM en p-p tON ISY IL IS ISC IN = 15 V, TA = 25 C, unless otherwise noted.) Min REF01A/E Typ Max 10.00 3.3 20 0.006 0.005 5 1.0 21 -0.5 30 10.03 30 0.010 0.008 1.4 10 -0.3 Min 9.95 3.0 REF01/H Typ Max 10.00 3.3 20 0.006 0.006 5 1.0 21 -0.5 30 10.05 30 0.010 0.010 1.4 Unit V % V p-p %/V %/mA s mA mA mA mA Conditions IL = 0 mA 9.97 RP = 10 k 3.0 0.1 Hz to 10 Hz VIN = 13 V to 33 V IL = 0 mA to 10 mA To 0.1% of Final Value No Load 10 -0.3 VO = 0 ELECTRICAL SPECIFICATIONS I = 0 mA, unless otherwise noted.) L (@ VIN = 15 V, -55 C TA +125 C for REF01A/E, and 0 C REF01A/E Typ Max 0.02 0.06 3.0 0.7 0.007 0.009 0.006 0.007 0.012 0.015 0.010 0.012 0.06 0.15 8.5 TA 70 C for REF01H and Parameter Symbol Conditions 0C TA 70C -55C TA +125C RP = 10 k 0C TA 70C -55C TA +125C 0C TA 70C -55C TA +125C Min Min REF01/H Typ Max 0.07 0.18 10.0 0.7 0.007 0.009 0.007 0.009 0.012 0.015 0.012 0.015 0.17 0.45 25.0 Unit % % ppm/C ppm/% Output Voltage Change VOT with Temperature 5, 6 Output Voltage TCVO Temperature Coefficient7 Change in VO Temperature Coefficient with Output Adjustment Line Regulation (VIN = 13 V to 33 V)2 Load Regulation (IL = 0 mA to 8 mA)2 %/V %/mA ELECTRICAL SPECIFICATIONS Parameter Output Voltage Output Adjustment Range Output Voltage Noise1 Line Regulation2 Load Regulation2 Turn-On Settling Time3 Quiescent Supply Current Load Current Sink Current4 Short Circuit Current Symbol VO VTRIM en p-p tON ISY IL IS ISC (@ VIN = 15 V, TA = 25 C, unless otherwise noted.) Min REF01C Typ Max 10.00 3.3 25 0.009 0.006 5 1.0 21 -0.5 30 10.10 35 0.015 0.015 1.6 Unit V % V p-p %/V %/mA s mA mA mA mA Conditions IL = 0 mA 9.90 RP = 10 k 2.7 0.1 Hz to 10 Hz VIN = 13 V to 33 V IL = 0 mA to 8 mA To 0.1% of Final Value No Load 8 -0.3 VO = 0 -2- REV. C REF01 ELECTRICAL SPECIFICATIONS Parameter Symbol Output Voltage Change VOT with Temperature5, 6 Output Voltage TCVO Temperature Coefficient7 Change in VO Temperature Coefficient with Output Adjustment Line Regulation2 Load Regulation2 (@ VIN = 15 V, 0 C TA 70 C for REF01CJ, REF01CZ, and -40 C TA +85 C for REF01CP and REF01CS, unless otherwise noted.) Min REF01C Typ Max 0.14 20 0.45 65 Unit % ppm/C Conditions RP = 10 k VIN = 13 V to 30 V IL = 0 to 5 mA 0.7 0.011 0.008 0.018 0.018 ppm/% %/V %/mA NOTES 1 Sample tested. 2 Line and load regulation specifications include the effect of self-heating. 3 Guaranteed by design. 4 During sink current test the device meets the output voltage specified. 5 VOT is defined as the absolute difference between the maximum output voltage and the minimum output voltage over the specified temperature range expressed as a percentage of 10 V: VOT = 6 V MAX - V MIN 10 V x 100 VOT specification applies trimmed to +10,000 V or untrimmed. TCVO is defined as Var divided by the temperature range, i.e. 7 TCVO 0o to + 70o C = ( ( ) VOT 0o to + 70o C 70 C o ( ) and ) TCVO -55o to + 125o C = Specifications are subject to change without notice. 15V 2 VIN VO 6 OUTPUT ) VOT -55o to + 125o C 180o C ( The REF01 trim terminal can be used to adjust the output voltage over a 10 V 300 mV range. This feature allows the system designer to trim system errors by setting the reference to a voltage other than 10 V. Of course, the output can also be set to exactly 10.000 V or to 10.240 V for binary applications. Adjustment of the output does not significantly affect the temperature performance of the device. The temperature coefficient change is approximately 0.7 ppm/C for 100 mV of output adjustment. REF01 TRIM GND 4 5 10k 2 6 Figure 1. Output Adjustment 2. INPUT VOLTAGE (VIN) 4. GROUND 5. TRIM 6. OUTPUT VOLTAGE (VOUT) +18V VIN 4 5 REF01 DIE SIZE 0.074 0.048 INCH, 3552 SQUARE MILS (1.88 1.22 mm, 2.29 SQUARE mm) GND -18V Figure 3. Dice Characteristics (125 C Tested Dice Available) Figure 2. Burn-In Circuit REV. C -3- REF01 WAFER TEST LIMITS unless otherwise noted.)* Parameter Output Voltage Output Adjustment Range Line Regulation Symbol VO V TRIM Conditions IL = 0 RP = 10 k VIN = 13 V to 33 V (@ VIN = 15 V, TA = 25 C for REF01N and REF01G devices, TA = 125 C for REF01NT and REF01GT devices, REF01NT Limit 10.05 9.95 REF01N Limit 10.03 9.97 3.0 0.01 REF01GT Limit 10.10 9.90 REF01G Limit 10.05 9.95 3.0 0.01 Unit V max V min % min %/V max 0.015 0.015 *Electrical tests are performed at wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed for standard product dice. Consult factory to negotiate specifications based on dice lot qualification through sample lot assembly and testing. TYPICAL ELECTRICAL CHARACTERISTICS (@ V Parameter Load Regulation Symbol Conditions IL = 0 mA to 10 mA IL = 0 mA to 8 mA, NT, GT @ 125C en p-p tON ISY IL IS ISC TCVO VO = 0 0.1 Hz to 10 Hz To 0.1% of Final Value NT, GT @ 125C No Load, NT, GT @ 125C IN = 15 V, TA = 25 C, unless otherwise noted.)* REF01N Typical REF01GT Typical REF01G Typical Unit REF01NT Typical 0.007 20 0.005 20 0.009 20 0.006 20 %/mA V p-p s mA mA mA mA Output Voltage Noise Turn-On Settling Time Quiescent Current Load Current Sink Current Short Circuit Current Output Voltage Temperature Coefficient 7.5 1.4 21 -0.5 30 5.0 1.0 21 -0.5 30 7.5 1.4 21 -0.5 30 5.0 1.0 21 -0.5 30 10 10 10 10 ppm/C *For 25C specifications of REF01NT and REF01GT, see REF01N and REF01G, respectively. -4- REV. C REF01 ABSOLUTE MAXIMUM RATINGS* Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 V Output Short Circuit Duration (to Ground or VIN) . . . . . . . . . . . . . . . . . . . . . . . . Indefinite Storage Temperature Range J, RC, and Z Packages . . . . . . . . . . . . . . . -65C to +150C P Package . . . . . . . . . . . . . . . . . . . . . . . . . -65C to +125C Operating Temperature Range REF01A . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to +125C REF01CJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to 70C REF01CP, REF01CS, REF01E, REF01H . . . . . . . . . . . . . . . . . . . . . . . . . -40C to +85C Junction Temperature (TJ) . . . . . . . . . . . . . -65C to +150C Lead Temperature (Soldering @ 60 sec) . . . . . . . . . . . . 300C *Absolute maximum ratings apply to both DICE and packaged parts, unless otherwise noted. Package Type TO-99 (J) 8-Pin Hermetic DIP (Z) 8-Pin Plastic DIP (P) 8-Pin SO (S) * JA* JC Unit C/W C/W C/W C/W 170 162 110 160 24 26 50 44 JA is specified for worst-case mounting conditions, i.e., JA is specified for device in socket for TO, CERDIP, and P-DIP packages; JA is specified for device soldered to printed circuit board for SO package. ORDERING GUIDE1 TA = 25 C VOS Max (mV) 30 30 50 100 100 100 TO-99 REF01EJ REF01CJ Package Description CERDIPS PDIP 8-Lead 8-Lead REF01AZ2 REF01EZ REF01HZ SOIC 8-Lead Operating Temperature Range MIL XIND XIND COM XIND XIND REF01HP REF01CP REF01HS3 REF01CS3 NOTES 1 Burn-in is available on commercial and industrial temperature range parts in Cerdip, plastic DIP, and TO-can packages. 2 For devices processed in total compliance to MIL-STD-883, add 883 after part number. Consult factory for 883 data sheet. 3 For availability and burn-in information on SO package, contact your local sales office. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the REF01 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE REV. C -5- REF01-Typical Performance Characteristics 10,000 VIN = 15V TA = 25 C LINE REGULATION - %/V PERCENT CHANGE IN OUTPUT VOLTAGE - % 76 66 LINE REGULATION - dB 0.0031 0.0100 0.0310 0.1000 0.3100 1.0000 VIN = 15V TA = 25 C 100 1k 10k 100k FREQUENCY - Hz 3.1000 10.000 1M 0.035 0.030 VIN = 15V 0.025 T = 25 C, T = 75 C A A 0.020 0.015 0.010 0.005 0 -10 DEVICE IMMERSED IN 75 C OIL BATH 0 10 20 30 TIME - s 40 50 60 56 46 36 26 16 0 10 OUTPUT NOISE - V p-p 1,000 100 10 10 100 1k 10k 100k FREQUENCY - Hz 1M TPC 1. Line Regulation vs. Frequency TPC 2. Output Wideband Noise vs. Bandwidth (0.1 Hz to Frequency Indicated) TPC 3. Output Change Due to Thermal Shock 35 SHORT CIRCUIT PROTECTION MAXIMUM LOAD CURRENT - mA 1.4 VIN = 15V LOAD REG - T/LOAD REG - 25 C 1.4 LINE REG - T/LINE REG - 25 C 30 25 20 15 10 5 TA = 25 C 0 10 15 20 25 INPUT VOLTAGE - V 30 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE - C 1.3 1.2 1.1 1.0 0.9 0.8 0.7 0.6 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE - C 500mW MAXIMUM DISSIPATION TPC 4. Maximum Load Current vs. Input Voltage TPC 5. Normalized Load Regulation ( IL = 10 mA) vs. Temperature TPC 6. Normalized Line Regulation vs. Temperature 30 VIN = 15V MAXIMUM LOAD CURRENT - mA QUIESCENT CURRENT - mA 1.3 VIN = 15V 1.2 25 20 1.1 15 10 1.0 0.9 0.8 0.7 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE - C 5 0 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE - C TPC 7. Maximum Load Current vs. Temperature TPC 8. Quiescent Current vs. Temperature -6- REV. C REF01 +15V 2 10k +15V MSB LSB 5.0k +15V 2 VIN 0.1 F VO 5 V+ GND 4 5.0k 6 5.0k B1 B2 B3 B4 B5 B6 B7 B8 lO 4 2 OP02 EO -15V +15V 6 5k 5 5k 15 B1 B2 B3 B4 B5 B6 B7 B8 14 0.01 F CC 16 3 13 ANALOG INPUT 0 TO +10V +15V VIN 0.1 F VO REF01 GND TRIM 4 3.9M lO 2 4 5.000k 3 2 8 CMP01C DAC08 7 4 lO REF01 DAC08 V- 5 6 7 8 9 10 1112 1 1 1k lO VLC CC -15V +15V -15V -15V 14 13 12 11 6 5 4 3 B1 B2 B3 B4 B5 B6 B7 B8 POS. FULL SCALE -1LSB ZERO SCALE NEG. FULL SCALE +1LSB NEG. FULL SCALE 1 1 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 1 0 1 0 E +4.960 0.000 -4.960 -5.000 7 CONNECT START TO CONVERSION COMPLETE FOR CONTINUOUS CONVERSIONS SERIAL OUTPUT START 1 10 AM2592 SUCCESSIVEAPPROXIMATION REGISTER 2 9 CONVERSION COMPLETE TTL CLOCK INPUT 2.25MHz Figure 4. D/A Converter Reference Figure 7. A/D Converter Reference +15V 2 VIN VO 6 +10V 1.1mA REF01 2 VIN 9V 0.1 F VO 6 + 10k 5 0.1% 10k 0.1% TRIM GND 4 +15V 0.1 F 5 REF01 9V TRIM GND 4 - 100k 10.000V -10V 5k OP02 -15V Figure 5. Precision Calibration Standard Figure 8. 10 V Reference 15V 2 VIN VO 6 VOLTAGE COMPLIANCE: -25V TO +3V IOUT 2 VIN VO 6 VOLTAGE COMPLIANCE: -3V TO +25V REF01 TRIM GND 4 5 R IOUT = 10V + 1mA R REF01 TRIM GND 4 5 R IOUT = 10V + 1mA R -15V IOUT Figure 6. Current Source Figure 9. Current Sink REV. C -7- REF01 PRECISION CURRENT SOURCE A current source with 25 V output compliance and excellent output impedance can be obtained using this circuit. REF01 keeps the line voltage and power dissipation constant in the device; the only important error consideration at room temperature is the negative supply rejection of the op amp. The typical 3 V/ V PSRR of the OP02E will create an 8 ppm change (3 V/V 25 V/10 V) in output current over a 25 V range. For example, a 10 mA current source can be built (R = 1 k) with 300 M output impedance. RO = 25 V 8 x 10-6 x 10 mA REFERENCE STACK WITH EXCELLENT LINE REGULATION Three REF01s can be stacked to yield 10.000 V, 20.000 V, and 30.000 V outputs. An additional advantage is near-perfect line regulation of the 10.0 V and 20.0 V output. A 32 V to 60 V input change produces an output change that is less than the noise voltage of the devices. A load bypass resistor (RB) provides a path for the supply current (ISY) of the 20.000 V regulator. In general, any number of REF01s can be stacked this way. For example, 10 devices will yield outputs of 10, 20, 30 . . . 100 V. The line voltage can change from 105 V to 130 V. However, care must be taken to ensure that the total load currents do not exceed the maximum usable current (typically 21 mA). +50V 32V TO 60V TRIMMED OUTPUTS VO 6 30.000V 2 6 VO VIN 2 VIN REF01 REF01 TRIM 5 10k GND 4 2 VIN C R (TRIM FOR CALIBRATION) GND 2 VIN VO 6 4 REF01 VO 6 20.000V REF01 2 VIN VO 6 TRIM GND 4 5 10k 10.000V GND 4 R C REF01 7 6 OP02E 4 RC = 10-5 SEC -5V IO = +10V R 2 3 VO = 0 TO +25V TRIM GND 4 5 10k RB 6.8k Figure 11. Reference Stack Figure 10. Precision Current Source SUPPLY BYPASSING For best results, it is recommended that the power supply pin is bypassed with a 0.1 F disc ceramic capacitor. -8- REV. C REF01 OUTLINE DIMENSIONS 8-Lead Ceramic Dip-Glass Hermetic Seal [CERDIP] (Q-8) Dimensions shown in inches and (millimeters) 8-Lead Metal Can [TO-99] (H-08B) Dimensions shown in inches and (millimeters) 0.005 (0.13) MIN 8 0.055 (1.40) MAX 5 REFERENCE PLANE 0.1850 (4.70) 0.1650 (4.19) 0.5000 (12.70) MIN 0.2500 (6.35) MIN 0.0500 (1.27) MAX 5 0.3700 (9.40) 0.3350 (8.51) 0.3350 (8.51) 0.3050 (7.75) PIN 1 1 4 0.310 (7.87) 0.220 (5.59) 0.1000 (2.54) BSC 0.1600 (4.06) 0.1400 (3.56) 0.0450 (1.14) 0.0270 (0.69) 0.100 (2.54) BSC 0.405 (10.29) MAX 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 0.060 (1.52) 0.015 (0.38) 0.150 (3.81) MIN SEATING 0.070 (1.78) PLANE 0.030 (0.76) 15 0 0.015 (0.38) 0.008 (0.20) 0.320 (8.13) 0.290 (7.37) 4 0.2000 (5.08) BSC 0.1000 (2.54) BSC 3 2 0.0190 (0.48) 0.0160 (0.41) 0.0210 (0.53) 0.0160 (0.41) BASE & SEATING PLANE 1 6 7 8 0.0400 (1.02) MAX 0.0400 (1.02) 0.0100 (0.25) 0.0340 (0.86) 0.0280 (0.71) 45 BSC CONTROLLING DIMENSIONS ARE IN INCH; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COMPLIANT TO JEDEC STANDARDS MO-002AK CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 8-Lead Standard Small Outline Package [SOIC] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 8-Lead Plastic Dual-in-Line Package [PDIP] (N-8) Dimensions shown in inches and (millimeters) 5.00 (0.1968) 4.80 (0.1890) 8 8 5 4 0.375 (9.53) 0.365 (9.27) 0.355 (9.02) 5 4.00 (0.1574) 3.80 (0.1497) 1 6.20 (0.2440) 5.80 (0.2284) 1 4 0.295 (7.49) 0.285 (7.24) 0.275 (6.98) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.015 (0.38) MIN SEATING PLANE 0.060 (1.52) 0.050 (1.27) 0.045 (1.14) 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) COPLANARITY SEATING 0.10 PLANE 1.75 (0.0688) 1.35 (0.0532) 8 0.25 (0.0098) 0 0.19 (0.0075) 0.50 (0.0196) 0.25 (0.0099) 45 0.100 (2.54) BSC 0.180 (4.57) MAX 0.150 (3.81) 0.135 (3.43) 0.120 (3.05) 0.51 (0.0201) 0.33 (0.0130) 1.27 (0.0500) 0.41 (0.0160) COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 0.150 (3.81) 0.130 (3.30) 0.110 (2.79) 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.015 (0.38) 0.010 (0.25) 0.008 (0.20) COMPLIANT TO JEDEC STANDARDS MO-095AA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) REV. C -9- REF01 Revision History Location 10/02--Data Sheet changed from REV. B to REV. C. Page Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Delete RC-SUFFIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Edits to Package Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Delete CP-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 -10- REV. C -11- -12- C00373-0-10/02(C) PRINTED IN U.S.A. |
Price & Availability of REF01HS |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |